Random good picture Not show

181. The effect of assembly tolerance on product assembly is researched in detail and the algorithm and program of total assembly cost is presented .

182. This paper presents a precise detection algorithm for locating the baseline of a text line, and the tolerance for baseline detection has been discussed.

183. Among them the automatic generation of dimension chain is the foundation of CAT and the described design function offers basis of tolerance analysis and tolerance synthesis.

184. Compared with seamless steel tube, hot tension reducing mill has welded pipe wall thickness tolerance small, cut head loss and product small yield higher advantages, can reduce the production cost.

185. Tolerance: Includes set up tolerance line regulation and load regulation.

186. Objective:To investigate the safety and superiority of blood drawing through an indwelling vein needle on in oral glucose tolerance test .

187. CONCLUSION: The lobster chitosan has the functions of declining the BS value and strengthening the sugar tolerance whereas unaffecting the normal glycogen metabolism in diabetic mice.

188. Then, the inspection of the part is simulated to evaluate geometric tolerance stack-up yield, and the calculation methods on different tolerancing principles are discussed.

189. A protocol is put forward, which can support crash-recovery model, make seamless fault- tolerance, and achieve the Consistency of multiple replicas in asynchronous system.

190. Due to the dielectric isolation of the measurement circuit layer, the sensor can work steadily under high temperature and possesses greater excess temperature tolerance.

191. Based on mate tree, the generation scheme of loop circuit and 3D assembly tolerance chains is put forth.

192. The germplasms of cold tolerance were not only widely existed on tropic, subtropic and temperature zone, but also difference with cold tolerance among plants of one landrace.

193. From tolerance to revolt, Beatrice realizes her self - salvation.

194. The extent of Lpr recovery and the photosynthetic parameters suggested that the tolerance of water stress in alfalfa was weak, while that of Longdong was stronger than Algonquin.Sentencedict

195. The experimental results showed that the AMPS/AA/DMDAAC - lignosulphonates graft copolymer has very good heat resistance, salt tolerance and inhibiting action when...

196. I'll wrap up with a few other nifty sysadmin tricks you can do with LVM2, including on-demand virtualization, improving fault tolerance with mirroring, and transparently encrypting a block device.

197. The cause of it mainly has some correlation with the physique, exercise content, exercise tolerance, competition, and arra...

198. The histopathology of resistance(tolerance)to Sclerotinia sclerotiorum in rape(Brassica napus)were studied.

199. The effect of CoCl 2 pretreatment on glucose transport activity of cultured newborn rat hippocampal neurons and its role in neuronal hypoxic tolerance were observed.

200. Famale Dragons are quite busy both physically and mentally. In the summertime, tact and tolerance are needed to avoid friction with a co-worker or someone close to you.

201. Maintaining the target Brix of the beverage in the lower tolerance range will save a company a lot of money.

202. The changes of baroreceptor reflex[sentencedict.com], especially the disturbance of CNS regulation function are the main factors causing the decrease of orthostatic tolerance after bed rest.

203. The resistance and tolerance of different varieties in Pleurotus Ostreatus to trichoderma sp. and Penicillun sp. were studied with plating method.

204. It may look severely deformed, but if checked, it is within the accepted tolerance.

205. Producing fewer printed sheets than specified or ordered. Trade customs permit a standard tolerance for overruns or underruns.

206. Tolerance design for assembly (TDFA) techniques essentially involve in two kinds of issues, assembly tolerance analysis and assembly tolerance synthesis.

207. The insulin sensitivity of animal models was quantified by insulin tolerance test, glucose tolerance test and gluconeogenesis test, etc.

208. Furthermore, the multi defect structure has greater tolerance of film thickness and incidence angle.

209. In this paper, we selected Medicago lupulina L. as experimental material and studied the physi-ecological responses and tolerance mechanism of Medicago lupulina L. to Cd stress with pot experiment.

210. This paper is based on the features of tooth profile and helix tolerance zone of transmission gears.