Synonym: barb, beam, beam of light, calamus, cheat, chicane, chouse, cock, diaphysis, dick, dig, gibe, irradiation, jibe, jockey, lance, light beam, pecker, peter, prick, putz, quill, ray, ray of light, rotating shaft, scape, screw, shaft of light, shot, slam, spear, tool. Similar words: chaff, south africa, aft, raft, daft, waft, graft, draft. Meaning: [ʃæft /ʃɑːft] 
n. 1. a line that forms the length of an arrow pointer 2. an aggressive remark directed at a person like a missile and intended to have a telling effect 3. a long rod or pole (especially the handle of an implement or the body of a weapon like a spear or arrow) 4. a column of light (as from a beacon) 5. the main (mid) section of a long bone 6. obscene terms for penis 7. a long pointed rod used as a weapon 8. a vertical passageway through a building (as for an elevator) 9. (architecture) upright consisting of the vertical part of a column 10. a vertical passage into a mine 11. a revolving rod that transmits power or motion 12. the hollow spine of a feather. v. 1. equip with a shaft 2. defeat someone in an expectation through trickery or deceit.
n. 1. a line that forms the length of an arrow pointer 2. an aggressive remark directed at a person like a missile and intended to have a telling effect 3. a long rod or pole (especially the handle of an implement or the body of a weapon like a spear or arrow) 4. a column of light (as from a beacon) 5. the main (mid) section of a long bone 6. obscene terms for penis 7. a long pointed rod used as a weapon 8. a vertical passageway through a building (as for an elevator) 9. (architecture) upright consisting of the vertical part of a column 10. a vertical passage into a mine 11. a revolving rod that transmits power or motion 12. the hollow spine of a feather. v. 1. equip with a shaft 2. defeat someone in an expectation through trickery or deceit. 
Random good picture Not show
61. Axial motion and misalignment (radial and angular offset) between the encoder shaft and the drive shaft are compensated by the coupling.
62. According to Oil Daily reports that the new low-friction characteristics of wavy liquid seal is formed on the surface of the shaft or by a sinusoidal waveform constitute special Lamiaceae.
63. In production of Spot welding machine of P131 transmission Shaft pressed assembly, there is a high requirement for the angle between two parts pressed in one tube.
64. Gear A , at the end of the drive shaft, and gear B, on the countershaft, are in constant mesh.
65. We require marine scrap like used propeller shaft, tail shaft, spare shaft, marine used equipments, used anchor chain, used shafting, used marine engine, used marine spares.
66. The general procedures for constructing subway are as follows: first excavate the shaft, then horizontal pass[sentencedict.com/shaft.html], finally ingate.
67. Sparated Bearing block for main transmission shaft Easy for maintenance and fix.
68. The shaft is connected with the cutting board movably, the two ends of the shaft are bent to insert in the holes arranged on the cutting board.
69. Lube lines are extended through shaft guards for easy accessibility.
70. Torque sensor can be used successfully in measuring friction torque between main shaft and motor in the non-load mechanical seal test.
71. The adjusting wheel is fixed on the rotating shaft, and the outer circumference of the adjusting wheel is provided with teeth of a first sequence.
72. The divided-flow two-level turbine engine with two pumps is composed of a turbine, a turbine shaft, a two-level booster pump wheel, a guide pulley and the expansion chamber shell.
73. With the proposed full-order observer, the flux linkage of motor can be accurately observed and high performance achieved without shaft encoder.
74. Swing shaft test bench is used to test alignment, calibration and accuracy of system under simulating swing condition in laboratory.
75. This accounts for the modern forms limb (limber has excrescent b, regardless of whether it means "shaft," "holes in timber," or "pliable"; none of them is related to limb) and crumb.
76. The nonmetal material insulating part is an inner insulating sleeve of the main shaft, which is sleeved at the lower part of the rotor driving shaft.
77. Simple cycle gas turbines are typically used for shaft horsepower applications without recovery of exhaust heat.
78. The inner race is keyed to the shaft. The outer race has h7 tolerance and should be fitted in housing with a k7 tolerance. Additional side notches provide for positive torque transmission.
79. Special radial play or shaft face clearance requirement could be made as specified in orders.
80. The section curve equation of main stirring shaft is obtained by deducting the screw profile curve formation process of the stirring kneader.
81. The invented generator comprises rotor on shaft fixed in body case as a rotatable bearing, and stator (8).
82. The design method mentioned has been beneficial in practice and provided a new basis for designing the same type of shaft coupling.
83. The setting optimization principle of compressible tie-in is brought forward; and it has important guidance meaning to design compressible shaft wall reasonably.
84. Design principle and construction technology of big calibre bedrock bench mark of shaft style are presented.
85. Elephants in zoos and circuses are typically moved with a tool called an ankus, a nasty-looking wooden shaft with a metal hook protruding from the top. It's banned at the sanctuary.
86. The hairspring produces the force to produce recovering force on the rotating shaft to ensure it coming back the initial point.
87. The shaft of the turbine is coupled to the rotor of the generator.
88. The utility model discloses a hinge for an insulating cover of a steel ladle, which comprises a fixed slot, a rotating slot, a rotating shaft, a pin key, a pin slot, and a supporting arm.
89. We want to buy Camshafts , Rockerarm, Rocker Shaft, General Casting Automotive Parts, Components and Spares.
90. The motor housing encloses the armature and pole pieces, holds the bearings that support the armature shaft, and provides the terminals for connecting the motor to the rest of the staring system.