Random good picture Not show

61. This paper introduces the new technology of salt bath soft nitriding treatment developed on the imported salt bath nitriding production line of the Styr engine crankshaft .

62. The deflection of crankpin and reciprocating rotation of piston were calculated according to the mathematic model based on the torque transmission theory of crankshaft.

63. The torsion bar absorbs torsional vibrations and isolates torsional vibrations due to inertia of the balance shaft caused by the crankshaft.

64. Each pair drives one crankpin , via two connecting rods, and the front of the crankshaft is geared down to a slower-running propeller.

65. When the stroke identification result mislead by the tooth counting error during the crankshaft angular velocity variation is too large, the system will identify the stroke again.

66. The crankshaft bearing is one of the most importance frictions in the internal combustion engine, whose lubricating property can impact on the internal combustion engine work performance directly.

67. Many problems are existed in original CA6110- 2 diesel engine crankshaft in its actual usage due to its 4- balancing- block structure.

68. Horizontal double sided NC combined drilling machine is specially designed for the machining of main shaft journal hole and crank arm journal straight oil hole of crankshaft with six cylinders.

69. Crankshaft surface rolling is one of the most important approaches to expand the crankshaft life.

70. I steam operating company, Moldova accessories, connecting rod , crankshaft, gears, ball, forging tools.

71. Depending on the requirements of the control system, the number of teeth on the cog wheel is defined to allow a resolution of approximately one pulse per degree of crankshaft revolution.

72. Position flywheel and O ring on crankshaft and align bolt holes.

73. The failure analyses were conducted on a diesel engine crankshaft made of ductile cast iron, which was nitrided. The fracture occurred at the web between the 1st crankpin and 2nd journal.

74. In recent years, with the developing of engine technology and the improving of Performance indicators such as power,[www.Sentencedict.com] the design technology of the engine crankshaft bearing is also keeping developing.

75. The crankshaft is an important part of the homogenizer. Its strength and rigidness have direct influence upon the properties of the whole machine.

76. The camshaft and crankshaft gears can be connected directly, or meshed.

77. The roughing and semi-finishing machining of the crankshaft spindle neck and crankpin is more time-consuming process.

78. I steam operating company, Moldova accessories, rod, crankshaft, gears, ball, forging tools.

79. The nationalization of engine crankshaft blank for Jetta , Bora and Golf car was realized.

80. The connecting rod is attached to the crankshaft at one end (big end) and to the piston at the other end (small end).

81. If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets .

82. By the time the crankshaft completes two revolutions, each cylinder in the engine will have gone through one power stroke.

83. It is quite correct in measuring the bending strength of connecting rod journal fillet of most normal structure crankshafts, but for some special structure crankshaft, it can't obtain ideal results.

84. The results show that the surface vibration crankcase is induced by 3 - D vibration of the crankshaft.

85. This paper presents a nonlinear autoregressive exogenous (NARX)model to approximate dynamics of crankshaft speed with the mass of the idle feeding fuel and the spark advance.

86. As the crankshaft rotates, the crankpin swings in a circle around the shaft.

87. The connecting rod links its large end to the crankshaft and its small end piston.

88. NC combined drilling machine is specially designed for the machining of main shaft journal hole and crank arm journal straight oil hole of crankshaft with six cylinders.

89. Based on the analysis of plastic flow law in crankshaft forming, the cause of typical forming defects, i. e. the folding existing in the crankshaft pin and crank arm was found out.

90. The grinding principle of crankshaft journal is introduced, the formation reason of position error is analyzed in detail, and the corresponding measures are proposed as well.