Random good picture Not show

61. It is a multiply Aluminium Polyester Laminated ducting with an en - capsulated high tensile steel wire helix.

62. They developed a new kind of lowalloy which has great tensile strength.

63. The satisfactory tensile strength of block copolymers may be attributed to the formation of allophanate crosslinks by the introduction of excess TDI.

64. The effect of steel bar diameter, reinforcement ratio, concrete tensile strength and cohesive strength between concrete and steel bar on cracking interval and width are analyzed.

65. When the ratio not more than 0.2, CFRP tensile strain can reach or exceed the permissible strain at ultimate capacity state, and therefore CFRP can work efficiently.

66. The micro - tensile processes of Chinese - fir and Masson pine are studied by synchrotron radiation light ( SRL ).

67. Aiming at solving the defects of exported Plast-Ripple-Duct tensile tester such as including all technical rules by halves and operating very complexly, the longitudinal tensile fixtures is improved.

67. Sentencedict.com is a online sentence dictionary, on which you can find good sentences for a large number of words.

68. Most fabrication codes require a minimum as-welded tensile strength of 24 ksi (165 MPa), which is a significant degradation.

69. The combinable fatliquor SC, phosphate fatliquor, sulfited sperm oil EJB can increase the tensile strength of chrome leather.

70. We have changed of feeding volume and arrange of selvage waste to discuss the effect of basis weight, tensile strength and elongation of nonwoven.

71. The analysis on fatigue cracks of the outer race of aero-bearing shows that the distribution of residual tensile stress on race surface could reduce its contact fatigue life.

72. Vertical alignment of QDsin multilayers is interpreted with lateral tensile strain at the growth front, when the thickness of the spacer layer is below a critical value.

73. The tensile modulus approximately equal to the compressive modulus of elasticity within the proportional limit.

74. The resistance reduction factor is suggested as a fixed value of 0.90, regardless of the strain level of the tensile steel reinforcement.

75. Tensile strength of sample special vehicle ZL205A aluminum alloy wheels made by counter pressure casting is with no heat crack, loosen or other defects.

76. At this point, tensile fracture partially occurred, as evidenced by some apparent necking.

77. Tensile properties of unidirectional laminates, with high strength and high modulus, are tested by electronic universal testing machine (model INSTRON-6025).

78. For processing the high tensile metals: carbon stell common alloy stell, hard bronze forgeable castiron. etc.

79. While the control of tensile force will adjust the thickness ratio within a small extent.

80. The important influence of efficiency factor of anchorage and tensile parameter were involved in the mathematic formula, which was an important reference of ascertaining the safe coefficient.

81. The methods are suggested to determine the tensile steps and the tensile forces of prestressed strands for decreasing the secondary bending moment along the axial of the penstock.

82. The bending, tensile and compressive experiments of ramie xylem of the variety "Huazhu-4" were conducted by using an universal testing machine "RGT-10".

83. Objective To evaluate the effects of varying load of vastus medialis oblique on the tensile stress at the proximal insertion of patellar tendon.

84. When it was tensile failure, the curve of stress-strain relationship was softening and the reinforcement only increased the angle of internal friction of soil.

85. As the vibration pressure amplitude increases, the impact strength and the tensile strength of the samples increase simultaneous. The structure of the samples were investigated by SEM, WAXD.

86. The inclusion of polyamide and alkyl ketene dimmer improved the mechanical properties of methylcellulose, especially the wet tensile strength. Testing of biodegradation activity showed that both St.

87. Tensile strength of the ethylamine ionomer increased with the sulfonate content increasing.

88. The strain contours are plotted by using tensile spline approximation.

89. The specimen deforms under a tensile stress applied parallel to the fibres.

90. With the same kind of loads, the buckling load keeps growing while the ratio of strip width to gauge or the tensile strain increases, and the complex grows obviously faster than the simple one.