Random good picture Not show

61. This paper presents the inner cooling theory that use the high insulating property and low boiling point materials instead of water as coolant in turbo-generator's stator windings.

62. In this paper, the modal of large turbogenerator stator end winding is studied using impulse technique.

63. Electromechanical integrated; Toroidal drive; Manufacture of the stator; Manufacture of the toroidal worm; Curved beam; Minimum energy method; Efficiency.

64. The vibrational characteristics of stator end winding and its fastener of a large turbo - generator are studied.

65. With the steady flux, stator resistance online tuning law is established.

66. During the measurement of welding contraction distortion for stator in a large hydropower station, the method is used well. And this me...

67. In this paper, the test for vibration mode of stator core of an electric- al motor are studied using the transfer function mode techniques.

68. Trailing edge blowing wake management technology was adopted to improve the flow of stator wake.

69. In stator current spectrum of induction motor, fault frequency component of rotor broken bar is very small and its frequency is close to basic wave, so it is difficult to obtain fault characteristic.

70. Decreasing the permittivity of cable insulation or separating the cable conductor can increase the cable surge impedance and wave velocity, so as to improve the voltage waveform on stator terminal.

71. Usage: suitable for auto dynamotor etc. motor stator coil terminal face shaping.

72. In the MATLAB, using a structured design method, a dual PWM converter control system model were established on the basis of the stator flux field vector control technology.

73. Namely , the frequency of the stator voltage is controlled to compensate for the error control ( FCC ).

74. This paper gives an account of the necessity of the computer-aided diagnosis for the practical stator curve of the two-acting vane pump, and sets forth the diagnosis theory and method.

75. The paper simulates the residual voltage of stator winding during the break period on the basis of accurate mathematical model for induction motor.

76. Relay protection for stator cooling water pump of unit 1 had experienced malfunction in Datang International Tuoketuo Power Generation Co.

77. The utility model relates to a permanent brushless direct current motor. The motor comprises a casing, a front end cover, a rear end cover, a stator, a rotor and a position sensor.

78. A new technology and equipment of annealing and bluing for finished stator and rotor of uncoated cold-rolled electric steel lamination in bell-type hytrogen furnace was introduced.

79. Calculating formulas and derived process of main angles of stator coil colloidization model at bottom end of spherical coordinate are introduced.

80. The requirement for leakage reactance on stator of PMSM supplied by voltage type inverter is analyzed, and some parameters are selected, such as electromagnetic load,[www.Sentencedict.com] slots shape of stator and so on.

81. Acording to fault condition of stator winding, sta- tor coils are combined into stator connected sets by using connection matric.

82. The new model for analyzing the dynamic characteristic of the stator frame has been set up, and the defect of the conventional model dynamic characteristic analysis of stator frame is remanded.

83. In this paper, the operation style of the 100% stator ground protection based on twice frequency separation is analysed, and the feasible improving scheme is put forward.

84. In asynchronous machine there exist main kinds of flux linkage, that is: rotor flux-linkage, air-gap flux-linkage and stator flux-linkage.

85. Several new types of stator ground protection without dead zone are reviewed.

86. And for having put an end to the feral wandering of these few giants, so that they became the princes of the gentes, he received the epithet Stator, stayer or establisher.

87. From the relative motion concept of rotor fixing and stator rotating, the experimental device (situation No. 3) for simulating the rotor blade tip clearance flow is designed.

88. The impact of harmonic on the simulation results of stator winding internal fault is further analyzed.

89. It is realized by adding a high frequency current to the original current of the stator and adding linear generator windings to magnetic pole.

90. Shell hole keyway generator is used to connect parts of the shell and the stator has a size large, long keyway, symmetrical high clamping difficulty with the knife and so on.