Random good picture Not show

211. When the content exceeds 03%, the underside shrinkage is enclosed and the internal shrinkage moves upwards gradually.

212. The utility model relates to a hot shrinkage pipe device which can evenly hot blow a plastic pipe to be deformed and quickly cold blow the deformed plastic pipe for shaping.

213. Based on our recent researching results, delayed ettringite formation ( DEF ) in massive shrinkage compensating concrete and its influence on the concrete properties are discussed to reply Mr.

214. The strength theory, dendritic bridging theory, solidification shrinkage reparing theory and CSC criterion, HCS criterion are stressed.

214. Wish you will love sentencedict.com and make progress everyday!

215. Results demonstrate the following optimum conditions for low - shrinkage sliver: hot stretch ratio of breaking machine, 1.

216. Self - desiccation: autogenous relative humidity change of a cementitious material system after setting. caused by chemical shrinkage.

217. But almost all the attention of the plastic shrinkage crack are focus on the medium and coarse sand concrete and the study of super fine one not found.

218. Acording to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right?

219. Chemical shrinkage: absolute volume reduction associated with the hydration reactions in a cementitious material.

220. The numerical simulation of 3D temperature field of castings during solidification process was carried out and the shrinkage cavity and porosity of sample castings were predicted using G/R method.

221. Stomatal dispersed shrinkage, shrinkage cavity, sonim and slag inclusion belong to this kind of defect.

222. The influence of compounding polypropylene fiber and expansion on flexure strength, impermeability and the shrinkage deformation is studied.

223. Effect of clay content and rock powder of gravel and sand on concrete property is studied in this paper, include compressive strength, impermeability and dry shrinkage.

224. The block has many advantages, such as simple production process, light weight, high strength, small conductivity and dry shrinkage etc. It is green building material product with good prospect.

225. Shrinkage and shrinkage porosity, stress and deformation often occurs during the production of heavy steel casting.

226. Carries on the appraisal once in a while according to the air shrinkage strain and coefficient of shrinkage's size by prompt the water loss relations to its road with the performance.

227. Dycosacryl UV and UV free radicals, compared to less shrinkage, and curing speed or slower.

228. The processing system of urban life rubbish should be characteristic of resource, harmlessness and shrinkage.

229. To amortize the intangible assets is the accounting method used to describe the shrinkage.

230. The theoretical analysis and calculation of the die swell and shrinkage for extruded tread out.

231. The study results indicate that the developed alloys have good flowability, smaller shrinkage rate, good anti-cracking ability and smaller casting stress tendency.

232. According to the causes of crack occurrence and the weather characteristics in the project area, it is key to prevent the cracks such as the plastic crack, dry crack and cold shrinkage crack.

233. And fracture spacing in concrete structure, shrinkage crack on ceramics driven by cooling and drying and so on are typical models of fracture spacing.

234. Using average shrinkage rates of injection-molded parts to decide the dimension of mold cavity can not satisfy the demand of high precision injection-molded parts.

235. The casting process was optimized by the simulation and the shrinkage hole, shrinkage porosity in the ductile iron hub were eliminated successfully.

236. The solidification process of the cross-section A-A of the high pressure inner cylinder is simulated and the shrinkage cavity position is predicated by means of utility software.

237. Shrinkage stress was found to increase linearly with cure temperature.

238. Using self-feeding in solidification can make good surface quality, no shrinkage casting defects of castings; the technology product yield of the casting greatly increases.

239. A new method was developed to simulate quantitatively the formation of shrinkage cavity in steel castings.

240. There is abnormal bottom shrinkage in Zn Al alloy castings and top riser has little effect on them.